Real repair prices from San Antonio Appliance Repair, LLC. Mickey Resendez has fixed appliances in San Antonio for 42 years, and these are the prices he actually charges. Find your appliance by the drawing, then find your problem. The price shown is the price you pay. Every price is a flat rate for the whole job, part and labor included.
Last updated October 25, 2026. More brands and appliances are being added.
How it works: Every price is a flat rate for the whole job, part and labor included, plus tax. The $75 service call is credited toward the repair. Find your appliance by the drawing, then look for your problem. These are flat rates, not estimates. For your style of appliance, the price you see here is the price you pay. Mickey texts you to confirm before he starts, so there are no surprises. Every part is a genuine original manufacturer (OEM) part, never a cheap knockoff.
More than one part? If your appliance needs more than one part, it is still one labor charge. Only the extra parts add to the price, and Mickey sometimes discounts an extra part, depending on its cost. He texts you the total before he starts. Second appliance? If another appliance at the same home needs a look on the same visit, it is usually just $20 more, depending on the job. Mickey will explain it while he is there.
Older Top-Load Washer (Direct-Drive)
How to tell: Knobs on a back panel, a lid on top, and a tall agitator in the middle. If you pull it out, the back has a small square motor held on with two clips.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Motor coupler #285753A | Motor runs, but the washer will not agitate or spin. Note: may need a new motor if the motor shaft is distorted (extra. Coupler and motor together: $397.74 + tax). | $201.20 + tax |
| Lid switch #3949238 / 3949247 | Fills but will not agitate or spin with the lid shut. Note: some lid switches cost less. Because part numbers vary by model, yours could be less. | $199.65 + tax |
| Drain pump #WP3363394 | Water stays in the tub, or leaks under the washer. | $232.00 + tax |
| Agitator dogs (4-pack) #80040 | Bottom of agitator turns but top part does not. | $171.99 + tax |
| Clutch kit #285785 | Slow spin, clothes come out soaking wet, brown dust under washer. | $214.93 + tax |
| Basket drive block Part # varies by model | Basket wobbles or turns freely by hand, or will not spin while the agitator still works. Clothes come out soaking wet. | $198.83 + tax |
| Water inlet valve Part # varies by model | Will not fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $253.57 + tax |
| Drive motor Part # varies by model | Hums or does nothing, coupler is good. | $361.54 + tax |
| Transmission (OEM) #3360629 | Loud grinding, oil under the washer, or agitator will not move. Only after checking: the coupler is good, the motor runs, and the motor shaft is not distorted. Note: transmission prices vary a lot by model. Mickey will text you the exact price, and he'll tell you honestly if a new washer makes more sense. | $476.76 + tax |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: Timers and the other switches on the control panel (water level, temperature, and speed switches) vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesNewer Top-Load Washer (Wash Plate or Agitator)
How to tell: Knobs on the back panel, some with a small number display. Inside, most have a low wash plate in the bottom, and some models have a tall agitator. Both use the same parts and prices. If your knob-style washer is newer than about 2010, it is this style.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Lid lock Part # varies by model | Won't start or spin, the lid-lock light blinks, or the lid won't lock. | $258.80 + tax |
| Shift actuator Part # varies by model | Washes but won't spin, or spins but won't wash. You may hear clicking. | $254.30 + tax |
| Clutch/cam kit Part # varies by model | Basket spins slowly or won't spin. Clothes come out soaking wet. | $218.20 + tax |
| Basket drive hub kit Part # varies by model | Basket wobbles, turns freely by hand, or clunks during spin. | $204.16–$233.87 + tax |
| Drive belt Part # varies by model | Motor runs but nothing turns, or you smell burning rubber. | $199.47 + tax |
| Motor capacitor Part # varies by model | Motor hums but won't start, or starts slowly. | $254.61 + tax |
| Drive motor Part # varies by model | Hums or does nothing. Only after checking the capacitor and belt. | $403.96 + tax |
| Drain pump Part # varies by model | Water stays in the tub, or the washer won't drain. Note: some pumps cost less. Because part numbers vary by model, yours could be much less. | $324.08 + tax |
| Water inlet valve Part # varies by model | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $257.32 + tax |
| Pressure switch hose Part # varies by model | Overfills, won't stop filling, or fills to the wrong level. | $197.81 + tax |
| Suspension rods (set of 4) Part # varies by model | Bangs, shakes, or walks across the floor during spin. | $304.44 + tax |
| Gearcase (transmission) Part # varies by model | Loud grinding, or won't wash or spin. Only after checking: the motor, belt, capacitor and shift actuator are good. Note: transmission prices vary a lot by model. Mickey will text you the exact price, and he'll tell you honestly if a new washer makes more sense. | $428.36 + tax |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The control board, timers and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesHE Top-Load Washer (Cabrio, Oasis)
How to tell: The model name (Cabrio or Oasis) is usually printed on the back panel, with a big round dial in the middle. Inside, a low wash plate in the bottom instead of a tall agitator.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Lid lock Part # varies by model | Won't start or spin, the lid-lock light blinks, or the lid won't lock. | $282.23 + tax |
| Shift actuator Part # varies by model | Washes but won't spin, or spins but won't wash. You may hear clicking. | $258.30 + tax |
| Basket drive hub kit Part # varies by model | Basket wobbles, turns freely by hand, or clunks during spin. | $213.13 + tax |
| Drain pump Part # varies by model | Water stays in the tub, or the washer won't drain. Note: pump prices vary by model. Mickey will text you the exact price. | $324.08 + tax |
| Water inlet valve Part # varies by model | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $292.42 + tax |
| Pressure switch hose Part # varies by model | Overfills, won't stop filling, or fills to the wrong level. | $197.81 + tax |
| Suspension rods (set of 4) Part # varies by model | Bangs, shakes, or walks across the floor during spin. | $309.43 + tax |
| Drive motor (rotor / stator) Part # varies by model | Won't wash or spin, hums, or grinds. Price depends on your model. Send Mickey your model number for a text quote. | Text for price |
| Rotor position (hall) sensor Part # varies by model | Starts and stops, or shows error codes during wash or spin. Send Mickey your model number for a text quote. | Text for price |
| Tub bearing Part # varies by model | Loud roaring or grinding during spin. On many of these the bearing is built into the tub, so Mickey quotes it by text, and he will tell you honestly if a new washer makes more sense. | Text for price |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The control board, motor control unit, timers and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesOlder Front-Load Washer (Duet)
How to tell: The door is on the front, with a round glass window. A control panel runs across the top with a soap drawer on the left and a big round dial in the middle. The panel usually says Duet (Kenmore models say HE3 or HE4). Many sit on a matching pedestal drawer.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Drain pump Part # varies by model | Water stays in the drum, or the washer won't drain or spin. | $363.26 + tax |
| Water inlet valve Part # varies by model | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $312.84 + tax |
| Door lock Part # varies by model | Won't start, the door-lock light blinks, or the door won't lock or won't unlock. | $313.50 + tax |
| Door boot seal Part # varies by model | Water leaks from the bottom of the door, or the rubber around the door opening is torn or moldy. | $304.80 + tax |
| Shock absorbers (pair) Part # varies by model | Bangs, shakes, or walks across the floor during spin. | $294.60 + tax |
| Drive belt Part # varies by model | Motor runs but the drum doesn't turn, or you hear squealing or smell burning rubber. | $204.50 + tax |
| Drive motor Part # varies by model | Drum won't turn even with a good belt, or the washer hums. Send Mickey your model number for a text quote. | Text for price |
| Tub bearing / spider arm Part # varies by model | Loud roaring or grinding during spin, or the drum feels loose. This is a big job on these washers, so Mickey quotes it by text, and he will tell you honestly if a new washer makes more sense. | Text for price |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The motor control unit, control board, timers and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesNewer Front-Load Washer
How to tell: The door is on the front, with a round glass window. Open the door and look at the sticker on the door rim: the model number starts with WFW. Many have a small square door at the bottom front for the drain filter.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Drain filter / coin trap cleaning No part needed | Won't drain or spin, and you hear the pump humming. Often a sock, coin or other small item is stuck in the drain filter, and no part is needed. | $165.00 + tax |
| Drain pump Part # varies by model | Water stays in the drum, or the washer won't drain or spin, and the drain filter is clear. | $363.26 + tax |
| Water inlet valve Part # varies by model | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $312.84 + tax |
| Door lock Part # varies by model | Won't start, the door-lock light blinks, or the door won't lock or won't unlock. | $258.80 + tax |
| Door boot seal Part # varies by model | Water leaks from the bottom of the door, or the rubber around the door opening is torn or moldy. | $324.80 + tax |
| Shock absorbers (pair) Part # varies by model | Bangs, shakes, or walks across the floor during spin. | $294.60 + tax |
| Water level pressure switch Part # varies by model | Overfills, won't fill, or stops partway with an error code. | $304.50 + tax |
| Drive motor (rotor / stator) Part # varies by model | Drum won't turn, the washer hums or grinds, or shows a motor error. Send Mickey your model number for a text quote. | Text for price |
| Tub bearing / spider arm Part # varies by model | Loud roaring or grinding during spin, or the drum feels loose. This is a big job on these washers, so Mickey quotes it by text, and he will tell you honestly if a new washer makes more sense. | Text for price |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The motor control unit, control board and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesTouch-Panel Top-Load Washer
How to tell: A flat touch panel with buttons across the back, and no knobs. Many have a 2-in-1 agitator in the middle whose top part lifts out. Example model numbers: WTW5057LW, WTW8127LW.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Lid lock Part # varies by model | Won't start or spin, the lid-lock light blinks, or the lid won't lock. | $263.60 + tax |
| Shift actuator Part # varies by model | Washes but won't spin, or spins but won't wash. You may hear clicking. | $274.30 + tax |
| Water inlet valve Part # varies by model | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $292.42 + tax |
| Drain pump Part # varies by model | Water stays in the tub, or the washer won't drain. | $354.08 + tax |
| Drive belt Part # varies by model | Motor runs but nothing turns, or you smell burning rubber. | $199.47 + tax |
| Motor capacitor Part # varies by model | Motor hums but won't start, or starts slowly. | $254.61 + tax |
| Clutch/cam kit Part # varies by model | Basket spins slowly or won't spin. Clothes come out soaking wet. | $218.20 + tax |
| Suspension rods (set of 4) Part # varies by model | Bangs, shakes, or walks across the floor during spin. | $304.44 + tax |
| Drive motor Part # varies by model | Hums or does nothing, even with a good capacitor and belt. Send Mickey your model number for a text quote. | Text for price |
| Gearcase (transmission) Part # varies by model | Loud grinding, or won't wash or spin, after the motor, belt, capacitor and shift actuator check out good. Mickey quotes it by text, and he will tell you honestly if a new washer makes more sense. | Text for price |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The touch panel, control board and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesMaytag Top-Load Washer with Knobs
How to tell: MAYTAG on a back panel with knobs, some with a small number display. Inside, a low wash plate or a tall agitator. Model numbers start with MVW, for example MVWC565FW, MVWX655DW or MVWB765FW.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Lid lock Part # varies by model | Won't start or spin, the lid-lock light blinks, or the lid won't lock. | $264.59 + tax |
| Shift actuator Part # varies by model | Washes but won't spin, or spins but won't wash. You may hear clicking. | $260.09 + tax |
| Clutch/cam kit Part # varies by model | Basket spins slowly or won't spin. Clothes come out soaking wet. | $223.99 + tax |
| Basket drive hub kit Part # varies by model | Basket wobbles, turns freely by hand, or clunks during spin. | $209.95–$239.66 + tax |
| Drive belt Part # varies by model | Motor runs but nothing turns, or you smell burning rubber. | $205.26 + tax |
| Motor capacitor Part # varies by model | Motor hums but won't start, or starts slowly. | $260.40 + tax |
| Drive motor Part # varies by model | Hums or does nothing. Only after checking the capacitor and belt. | $409.75 + tax |
| Drain pump Part # varies by model | Water stays in the tub, or the washer won't drain. Note: some pumps cost less. Because part numbers vary by model, yours could be much less. | $329.87 + tax |
| Water inlet valve Part # varies by model | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $263.11 + tax |
| Pressure switch hose Part # varies by model | Overfills, won't stop filling, or fills to the wrong level. | $203.60 + tax |
| Suspension rods (set of 4) Part # varies by model | Bangs, shakes, or walks across the floor during spin. | $310.23 + tax |
| Gearcase (transmission) Part # varies by model | Loud grinding, or won't wash or spin. Only after checking: the motor, belt, capacitor and shift actuator are good. Note: transmission prices vary a lot by model. Mickey will text you the exact price, and he'll tell you honestly if a new washer makes more sense. | $434.15 + tax |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The control board, timers and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesMaytag Bravos HE Top-Load Washer
How to tell: Says Bravos on the back panel, with a big round dial in the middle. Inside, a low wash plate instead of a tall agitator. Model numbers look like MVWB800VQ or MVWB950YW. Not sure which Maytag you have? Send Mickey your model number.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Lid lock Part # varies by model | Won't start or spin, the lid-lock light blinks, or the lid won't lock. | $288.02 + tax |
| Shift actuator Part # varies by model | Washes but won't spin, or spins but won't wash. You may hear clicking. | $264.09 + tax |
| Basket drive hub kit Part # varies by model | Basket wobbles, turns freely by hand, or clunks during spin. | $218.92 + tax |
| Drain pump Part # varies by model | Water stays in the tub, or the washer won't drain. Note: pump prices vary by model. Mickey will text you the exact price. | $329.87 + tax |
| Water inlet valve Part # varies by model | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $298.21 + tax |
| Pressure switch hose Part # varies by model | Overfills, won't stop filling, or fills to the wrong level. | $203.60 + tax |
| Suspension rods (set of 4) Part # varies by model | Bangs, shakes, or walks across the floor during spin. | $315.22 + tax |
| Drive motor (rotor / stator) Part # varies by model | Won't wash or spin, hums, or grinds. Price depends on your model. Send Mickey your model number for a text quote. | Text for price |
| Rotor position (hall) sensor Part # varies by model | Starts and stops, or shows error codes during wash or spin. Send Mickey your model number for a text quote. | Text for price |
| Tub bearing Part # varies by model | Loud roaring or grinding during spin. On many of these the bearing is built into the tub, so Mickey quotes it by text, and he will tell you honestly if a new washer makes more sense. | Text for price |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The control board, motor control unit, timers and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesMaytag Top-Load Washer, 2022 and Newer
How to tell: The newest Maytag top-loaders. Model numbers end in M plus a color letter, for example MVW5035MW or MVW6500MW. Many have a 2-in-1 agitator whose top part lifts out.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Lid lock Part # varies by model | Won't start or spin, the lid-lock light blinks, or the lid won't lock. | $269.39 + tax |
| Shift actuator Part # varies by model | Washes but won't spin, or spins but won't wash. You may hear clicking. | $280.09 + tax |
| Water inlet valve Part # varies by model | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $298.21 + tax |
| Drain pump Part # varies by model | Water stays in the tub, or the washer won't drain. | $359.87 + tax |
| Drive belt Part # varies by model | Motor runs but nothing turns, or you smell burning rubber. | $205.26 + tax |
| Motor capacitor Part # varies by model | Motor hums but won't start, or starts slowly. | $260.40 + tax |
| Clutch/cam kit Part # varies by model | Basket spins slowly or won't spin. Clothes come out soaking wet. | $223.99 + tax |
| Suspension rods (set of 4) Part # varies by model | Bangs, shakes, or walks across the floor during spin. | $310.23 + tax |
| Drive motor Part # varies by model | Hums or does nothing, even with a good capacitor and belt. Send Mickey your model number for a text quote. | Text for price |
| Gearcase (transmission) Part # varies by model | Loud grinding, or won't wash or spin, after the motor, belt, capacitor and shift actuator check out good. Mickey quotes it by text, and he will tell you honestly if a new washer makes more sense. | Text for price |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The touch panel, control board and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesMaytag Epic Front-Load Washer
How to tell: The door is on the front, with a round glass window, and the panel says Epic or Epic Z. Model numbers start with MFW, MHWE or MHWZ.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Drain pump Part # varies by model | Water stays in the drum, or the washer won't drain or spin. | $369.05 + tax |
| Water inlet valve Part # varies by model | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $318.63 + tax |
| Door lock Part # varies by model | Won't start, the door-lock light blinks, or the door won't lock or won't unlock. | $319.29 + tax |
| Door boot seal Part # varies by model | Water leaks from the bottom of the door, or the rubber around the door opening is torn or moldy. | $310.59 + tax |
| Shock absorbers (pair) Part # varies by model | Bangs, shakes, or walks across the floor during spin. | $300.39 + tax |
| Drive belt Part # varies by model | Motor runs but the drum doesn't turn, or you hear squealing or smell burning rubber. | $210.29 + tax |
| Drive motor Part # varies by model | Drum won't turn even with a good belt, or the washer hums. Send Mickey your model number for a text quote. | Text for price |
| Tub bearing / spider arm Part # varies by model | Loud roaring or grinding during spin, or the drum feels loose. This is a big job on these washers, so Mickey quotes it by text, and he will tell you honestly if a new washer makes more sense. | Text for price |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The motor control unit, control board, timers and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesNewer Maytag Front-Load Washer
How to tell: The door is on the front, with a round glass window. Open the door and look at the sticker on the door rim: the model number starts with MHW, for example MHW5630HW or MHW8630HC.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Drain filter / coin trap cleaning No part needed | Won't drain or spin, and you hear the pump humming. Often a sock, coin or other small item is stuck in the drain filter, and no part is needed. | $165.00 + tax |
| Drain pump Part # varies by model | Water stays in the drum, or the washer won't drain or spin, and the drain filter is clear. | $369.05 + tax |
| Water inlet valve Part # varies by model | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $318.63 + tax |
| Door lock Part # varies by model | Won't start, the door-lock light blinks, or the door won't lock or won't unlock. | $264.59 + tax |
| Door boot seal Part # varies by model | Water leaks from the bottom of the door, or the rubber around the door opening is torn or moldy. | $330.59 + tax |
| Shock absorbers (pair) Part # varies by model | Bangs, shakes, or walks across the floor during spin. | $300.39 + tax |
| Water level pressure switch Part # varies by model | Overfills, won't fill, or stops partway with an error code. | $310.29 + tax |
| Drive motor (rotor / stator) Part # varies by model | Drum won't turn, the washer hums or grinds, or shows a motor error. Send Mickey your model number for a text quote. | Text for price |
| Tub bearing / spider arm Part # varies by model | Loud roaring or grinding during spin, or the drum feels loose. This is a big job on these washers, so Mickey quotes it by text, and he will tell you honestly if a new washer makes more sense. | Text for price |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The motor control unit, control board and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesFrigidaire Front-Load Washer
How to tell: FRIGIDAIRE on the front panel, and the door is on the front with a round glass window. Open the door and look at the sticker on the door frame: the model number starts with FFFW, FAFW, LTF, ATF or GLTF.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Drain filter / coin trap cleaning No part needed | Won't drain or spin, and you hear the pump humming. Often a sock, coin or other small item is stuck in the drain filter, and no part is needed. | $165.00 + tax |
| Drain pump Part # varies by model | Water stays in the drum, or the washer won't drain or spin, and the drain filter is clear. | $354.80 + tax |
| Water inlet valve Part # varies by model | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $344.80 + tax |
| Door lock Part # varies by model | Won't start, the door-lock light blinks, or the door won't lock or won't unlock. | $258.80 + tax |
| Door boot seal Part # varies by model | Water leaks from the bottom of the door, or the rubber around the door opening is torn or moldy. | $294.80 + tax |
| Shock absorbers (pair) Part # varies by model | Bangs, shakes, or walks across the floor during spin. | $264.80 + tax |
| Motor control board Part # varies by model | Won't tumble or spin, or shows a motor error. Send Mickey your model number for a text quote. | Text for price |
| Spider arm / tub bearing Part # varies by model | Loud grinding or roaring during spin, or the drum sags or wobbles. Frigidaire spider arms often corrode and break. Mickey quotes it by text, and he will tell you honestly if a new washer makes more sense. | Text for price |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The motor control board, main control board and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesOlder Frigidaire Top-Load Washer
How to tell: All white, with a flat upright panel on the back: three small knobs on the left and a big timer dial on the right. A plain white lid, and a tall agitator inside. Model numbers often start with GLWS, FWS or FWX, for example GLWS1439FS.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Lid switch #134936800 | Fills but won't agitate or spin with the lid closed. | $264.80 + tax |
| Water inlet valve #134890600 | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $274.80 + tax |
| Drain pump #137221600 | Water stays in the tub, or the washer won't drain. | $354.80 + tax |
| Drive belt #134511600 | Motor runs but the washer won't agitate or spin, or you smell burning rubber. | $199.80 + tax |
| Suspension springs / snubber Part # varies by model | Bangs, shakes, or walks across the floor during spin. Send Mickey your model number for a text quote. | Text for price |
| Drive motor / transmission / timer Part # varies by model | Hums, does nothing, grinds, or the timer won't advance. Mickey quotes it by text, and he will tell you honestly if a new washer makes more sense. | Text for price |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: Timers and the other switches on the control panel vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesFrigidaire Top-Load Washer
How to tell: FRIGIDAIRE on the back panel, and a lid on top. Look on the sticker under the lid: the model number starts with FFTW or FTW, for example FFTW4120SW.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Lid lock #5304511338 | Won't start or spin, the lid-lock light blinks, or the lid won't lock. | $274.80 + tax |
| Lid switch #5304520868 | Won't start or won't spin with the lid closed. | $224.80 + tax |
| Water inlet valve Part # varies by model | Won't fill, fills slowly, only hot or only cold, or keeps filling with the washer off. | $304.80 + tax |
| Drain pump #5304511363 | Water stays in the tub, or the washer won't drain. Note: this pump costs more than most. Mickey will tell you honestly if a new washer makes more sense. | $418.66 + tax |
| Drain pump retractor (shifter) Part # varies by model | Washes but won't spin, or won't drain, and you may hear clicking. Send Mickey your model number for a text quote. | Text for price |
| Control board / drive motor Part # varies by model | Does nothing, hums, or shows an error code. Send Mickey your model number for a text quote. | Text for price |
Hoses
Add new hoses during any repair for just the hose price. Hoses replaced by themselves are the hose price plus the flat repair charge.
| Fill hose, quality standard | $14.00 each |
| Fill hose, braided stainless steel | $23.72 each |
| Steam dryer / washer hose kit | $76.41 kit |
Cosmetic and structural parts (lid, hinges, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The control board, motor and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesDryer with the Lint Screen on Top (29 inch)
How to tell: The lint screen pulls out of a slot on the top of the dryer, and the controls are on a back panel. Electric and gas models use the same style.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Thermal fuse Part # varies by model | Won't start or run at all. On these Whirlpool-built dryers the thermal fuse cuts power to the motor, not the heat. A clogged vent usually blows it, so Mickey checks your vent too. | $194.80 + tax |
| Thermostat (cycling or high-limit) Part # varies by model | Too hot, not hot enough, or the heat cuts in and out. | $209.80 + tax |
| Heating element (electric) Part # varies by model | Electric dryer runs and tumbles but stays cold. | $244.80 + tax |
| Gas igniter Part # varies by model | Gas dryer runs but no heat, and the igniter does not glow. | $224.80 + tax |
| Gas valve coils (set) Part # varies by model | Gas dryer igniter glows, then goes out without lighting, or the heat works for a while and then stops. | $219.80 + tax |
| Flame sensor Part # varies by model | Gas dryer igniter glows but the flame never lights, or the igniter never glows at all. | $209.80 + tax |
| Drive belt Part # varies by model | Drum won't turn. On newer models a broken belt trips the belt switch, which cuts power to the motor, so the dryer won't run at all. | $199.80 + tax |
| Idler pulley Part # varies by model | Loud squealing or squeaking while it runs. | $204.80 + tax |
| Drum rollers Part # varies by model | Thumping, rumbling or roaring while the drum turns. | $214.80 + tax |
| Drum rebuild (belt, idler pulley and rollers) Part # varies by model | Noisy and worn. All the moving parts are replaced in one job, for less than doing them one at a time. | $274.80 + tax |
| Door switch Part # varies by model | Won't start with the door closed, or the drum light stays off. | $204.80 + tax |
| Drive motor Part # varies by model | Hums but won't start, or won't run at all, after the thermal fuse, belt and door switch check out good. | $354.80 + tax |
Cosmetic and structural parts (door, hinges, handle, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The timer, control board and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesFront-Load Style Dryer (Lint Screen in the Door, 27 inch)
How to tell: Matches a front-load washer, usually with a round door. The lint screen sits inside the bottom of the door opening. Electric and gas models use the same style.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Control board repair (by hand) No part needed | Won't start, or shows F01. When the board can be repaired by hand (a relay or solder joints), Mickey fixes it instead of selling you a new board. | $210.00 + tax |
| Thermal fuse Part # varies by model | Won't start or run at all. On these Whirlpool-built dryers the thermal fuse cuts power to the motor, not the heat. A clogged vent usually blows it, so Mickey checks your vent too. | $194.80 + tax |
| Thermostat (cycling or high-limit) Part # varies by model | Too hot, not hot enough, or the heat cuts in and out. | $209.80 + tax |
| Heating element (electric) Part # varies by model | Electric dryer runs and tumbles but stays cold. | $284.23 + tax |
| Gas igniter Part # varies by model | Gas dryer runs but no heat, and the igniter does not glow. | $224.80 + tax |
| Gas valve coils (set) Part # varies by model | Gas dryer igniter glows, then goes out without lighting, or the heat works for a while and then stops. | $219.80 + tax |
| Flame sensor Part # varies by model | Gas dryer igniter glows but the flame never lights, or the igniter never glows at all. | $209.80 + tax |
| Drive belt Part # varies by model | Won't run at all. On these dryers a broken belt trips the belt switch, which cuts power to the motor. A very common repair on this style. | $204.80 + tax |
| Idler pulley Part # varies by model | Loud squealing or squeaking while it runs. | $209.80 + tax |
| Drum rollers Part # varies by model | Thumping, rumbling or roaring while the drum turns. | $224.80 + tax |
| Drum rebuild (belt, idler pulley and rollers) Part # varies by model | Noisy and worn. All the moving parts are replaced in one job, for less than doing them one at a time. | $289.80 + tax |
| Door switch Part # varies by model | Won't start with the door closed, or the drum light stays off. | $204.80 + tax |
| Drive motor Part # varies by model | Hums but won't start, or won't run at all, after the thermal fuse, belt and door switch check out good. | $354.80 + tax |
Cosmetic and structural parts (door, hinges, handle, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: A new control board and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesMaytag Dryer with the Lint Screen on Top (29 inch)
How to tell: MAYTAG on the back panel, and the lint screen pulls out of a slot on the top of the dryer. Model numbers start with MED (electric) or MGD (gas), for example MEDC465HW or MGDB765FW. Electric and gas models use the same style.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Thermal fuse Part # varies by model | Won't start or run at all. On these Whirlpool-built dryers the thermal fuse cuts power to the motor, not the heat. A clogged vent usually blows it, so Mickey checks your vent too. | $200.59 + tax |
| Thermostat (cycling or high-limit) Part # varies by model | Too hot, not hot enough, or the heat cuts in and out. | $215.59 + tax |
| Heating element (electric) Part # varies by model | Electric dryer runs and tumbles but stays cold. | $250.59 + tax |
| Gas igniter Part # varies by model | Gas dryer runs but no heat, and the igniter does not glow. | $230.59 + tax |
| Gas valve coils (set) Part # varies by model | Gas dryer igniter glows, then goes out without lighting, or the heat works for a while and then stops. | $225.59 + tax |
| Flame sensor Part # varies by model | Gas dryer igniter glows but the flame never lights, or the igniter never glows at all. | $215.59 + tax |
| Drive belt Part # varies by model | Drum won't turn. On newer models a broken belt trips the belt switch, which cuts power to the motor, so the dryer won't run at all. | $205.59 + tax |
| Idler pulley Part # varies by model | Loud squealing or squeaking while it runs. | $210.59 + tax |
| Drum rollers Part # varies by model | Thumping, rumbling or roaring while the drum turns. | $220.59 + tax |
| Drum rebuild (belt, idler pulley and rollers) Part # varies by model | Noisy and worn. All the moving parts are replaced in one job, for less than doing them one at a time. | $280.59 + tax |
| Door switch Part # varies by model | Won't start with the door closed, or the drum light stays off. | $210.59 + tax |
| Drive motor Part # varies by model | Hums but won't start, or won't run at all, after the thermal fuse, belt and door switch check out good. | $360.59 + tax |
Cosmetic and structural parts (door, hinges, handle, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: The timer, control board and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesMaytag Front-Load Style Dryer (Lint Screen in the Door, 27 inch)
How to tell: Matches a Maytag front-load washer, usually with a round door, and the lint screen sits inside the bottom of the door opening. Model numbers start with MED or MGD, for example MED9700SQ or MED5630HW.
✓ Flat rate: what you see is what you pay for this style
✓ Genuine OEM parts only
| Repair | What you notice | Flat-rate price |
|---|---|---|
| Control board repair (by hand) No part needed | Won't start, or shows F01. When the board can be repaired by hand (a relay or solder joints), Mickey fixes it instead of selling you a new board. | $210.00 + tax |
| Thermal fuse Part # varies by model | Won't start or run at all. On these Whirlpool-built dryers the thermal fuse cuts power to the motor, not the heat. A clogged vent usually blows it, so Mickey checks your vent too. | $200.59 + tax |
| Thermostat (cycling or high-limit) Part # varies by model | Too hot, not hot enough, or the heat cuts in and out. | $215.59 + tax |
| Heating element (electric) Part # varies by model | Electric dryer runs and tumbles but stays cold. | $290.02 + tax |
| Gas igniter Part # varies by model | Gas dryer runs but no heat, and the igniter does not glow. | $230.59 + tax |
| Gas valve coils (set) Part # varies by model | Gas dryer igniter glows, then goes out without lighting, or the heat works for a while and then stops. | $225.59 + tax |
| Flame sensor Part # varies by model | Gas dryer igniter glows but the flame never lights, or the igniter never glows at all. | $215.59 + tax |
| Drive belt Part # varies by model | Won't run at all. On these dryers a broken belt trips the belt switch, which cuts power to the motor. A very common repair on this style. | $210.59 + tax |
| Idler pulley Part # varies by model | Loud squealing or squeaking while it runs. | $215.59 + tax |
| Drum rollers Part # varies by model | Thumping, rumbling or roaring while the drum turns. | $230.59 + tax |
| Drum rebuild (belt, idler pulley and rollers) Part # varies by model | Noisy and worn. All the moving parts are replaced in one job, for less than doing them one at a time. | $295.59 + tax |
| Door switch Part # varies by model | Won't start with the door closed, or the drum light stays off. | $210.59 + tax |
| Drive motor Part # varies by model | Hums but won't start, or won't run at all, after the thermal fuse, belt and door switch check out good. | $360.59 + tax |
Cosmetic and structural parts (door, hinges, handle, cabinet, panels, knobs, leveling legs) are priced by your model and part number. Send Mickey your model number and he will text you the price.
Note: A new control board and other control panel parts vary a lot in price, depending on your part number and current pricing. Send Mickey your model number and he will text you that price before any work starts.
↑ Back to the list of appliancesAbout these prices: The price shown is what you pay when Mickey's diagnosis at your home confirms your appliance needs that repair. If it turns out to need a different part, or a part that costs more on your model, Mickey texts you the new price first. Nothing changes without your OK, and no work starts until you agree. If a part isn't in stock at one of Mickey's local San Antonio distributors and has to be shipped, he tells you the shipping cost up front. Mickey updates these flat rates when part costs change. The price he texts you is the price you pay.
Warranty: Every part Mickey installs is covered for 1 year. Labor and the service call are covered for 30 days. Consumable items like water filters, light bulbs and air filters are not covered.
Don’t see your appliance?
Ask Mickey’s AI Knight for an instant repair quote on any washer, dryer, refrigerator, dishwasher, oven or microwave. You can also call or text (210) 374-5977, or pick a time and book online.